PIST-2MP+ PCMCIA, 2xE1/T1/J1

2 E1/T1/J1 interfaces. Software switchable between all modes.
1 full duplex span of monitoring.
High-impedance mode for monitor applications (PIST-2MP).
Software-switchable 20dB signal amplifier and high-impedance mode for monitor applications (PIST-2MP+).
PCMCIA host bus interface.
Two on-board digital signal processors (DSPs)
Single bit error simulation mode (PIST-2MP+/PIST-2MP-EX/PIST-2MP-CST/PIST-2MP-PRO).

PIST-2MP: 80 MIPS processing power each.
PIST-2MP+/PIST-2MP-EX/PIST-2MP-CST: 120 MIPS processing power each.
PIST-2MP-PRO: 160 MIPS processing power each.

Board Specification	PCMCIA Type II card
Host Bus Interface	PCMCIA Type II card I/O mapped, SW configurable IRQ
Network Interfaces	2 E1/T1/J1 (software switchable)
Line Termination	75 Ohm and 100/120 Ohm or high impedance
DSP	PIST-2MP: 2 x TI TMS320C548 (80 MIPS) PIST-2MP+: 2 x TI TMS320C549 with (120 MIPS) PIST-2MP-EX: 2 x TI TMS320C5410A (120 MIPS) PIST-2MP-CST: 2 x TI TMS320C54CST (120 MIPS) PIST-2MP-PRO: 2 x TI TMS320VC5416 (160 MIPS)
DSP Programming Interface	Software development kit in ANSI C and C++ Open interface with standard third-party tools
DSP Applications	DTMF, MF, FSK, and generic tone (e.g., dial-tone and call progress tone) generation and detection Speech compression, encoding and decoding HDLC processing
E1/T1/J1 Frame Formats	Doubleframe, CRC Multiframe (E1 mode) F4, SF (or D4), ESF (or F24), SLC96 (T1/J1 mode)
E1/T1/J1 Line Codes	HDB3, B8ZS, AMI, AMI with ZCS
E1/T1/J1 Signalling Types	Channel associated (robbed bit) Common channel
Clocking sources	Onboard oscillator Incoming E1/T1/J1 span
Testing Features	Full access to F, Y, Si, and Sa bits in E1 mode Full access to FS/DL-bits in T1 mode (including support for the DL-channel protocol according to T1.403-1989 ANSI or to AT&T TR54016 specification), and programmable line build-out in T1/J1mode Transparent mode and programmable transmit pulse shape and input threshold Alarm insertion and detection
EMC and Safety Testing/Certification	FCC Part 15 (CFR47, Part 15, Subpart B) CE EMC (EN61326-1 Class B Equipment, AS/NZS 2064 Class B Limits) Safety EN60950 and UL60950 (dongle only)
Connector	RJ45/RJ48C in dongle (two dongles per board)
Power Requirements/Environmental Data	Power consumption: 3.0W for PIST-2MP; 2.8W for PIST-2MP+ Temperature: operating, 0 C to +50 C; non-operating, -40 C to +60 C Humidity: operating, 5% to 80% RH (%relative humidity) at up to +30 C, and 5% to 30% RH above +30o C up to +50 C non-condensing; non-operating, 5% to 80% RH at up to +30o C, and 5% to 30% RH above +30 C up to +50 C non-condensing
Device Drivers	Windows NT 4.0 Windows 2000 Windows XP Linux
API	Device Driver SDK DSP SDK