PIST-8-TDM-PCI-Plus

Features

The PIST-8-TDM-PCI-Plus product has the following features:

PIST-8-TDM-PCI-Plus
  • 8 T1/E1/J1 interfaces
  • Software switchable between T1, E1 and J1
  • PCI host bus interface (full-size board)
  • 32-Bit Data DMA transfer
  • H.100 Computer Telephony bus interface
  • 4-channel Codec
  • Software switchable line termination (75 and 100/120 ohm)
  • Optional high stability oven controlled oscillator
  • T1/E1 span frequency measurement
  • Support for all common T1/E1/J1 Frame Formats and Line Codes

Technical Specifications

Board Specification
  • Full-size PCI board
Host Bus Interface
  • Supports PCI rev 2.1, rev 2.2, rev 2.3 (3.3volt signaling) and rev 3.0
  • 32-bit burst DMA
Network Interfaces
  • 8 T1/J1 or E1 interfaces (software switchable)
  • 75 Ohm, 100/120 Ohm, high-z termination, monitor amplifier
H.100 Interface
  • 32 x 2, 4, or 8 Mbit/s board-to-board highways
  • 256 duplex channels switchable between adapters, 1024 channels switchable locally
DSP Resources (with optional ASM daughterboard)
  • PIST-55x4-ASM: 4 x TI TMS320VC5510 (400 MIPS) with 16MB SDRAM each
HDLC Resources
  • Support for 1 HDLC channel per access port
  • ASM modules offer additional HDLC channels with support for super- and sub-channels
T1/E1/J1 Frame Formats
  • Doubleframe, CRC Multiframe (E1 mode)
  • F4, SF (or D4), ESF (or F24), SLC96 (T1/J1 mode)
T1/E1/J1 Line Codes
  • HDB3, B8ZS, AMI, AMI with ZCS
T1/E1/J1 Signaling Types
  • Channel associated (robbed bit)
  • Common channel
Clocking Sources
  • On-board oscillator (high-stability oven-controlled oscillator option available)
  • Incoming T1/E1/J1
  • H.100 clock
  • External clock
Connector
  • 50-pin Centronix, 3-foot cable to harmonica with RJ45/RJ48C connectors for E1/T1/J1, and RJ11 connectors for handsets
Testing Features
  • Full access to F, Y, Si, and Sa bits in E1 mode
  • Full access to FS/DL-bits in T1 mode (including support for the DL-channel protocol according to T1.403-1989 ANSI or to AT&T TR54016 specification), and programmable line build-out in T1/J1 mode
  • Transparent mode and programmable transmit pulse shape and input threshold
  • Alarm insertion and detection, loop codes, channel loopback and PRBS
  • T1/E1 span frequency measurement
Phone Features
  • 4 analog interfaces (Codecs) for speaker, microphone, handset, or modem connections
Power Requirements / Environmental Data
  • Power consumption: 4.1W
  • Temperature: operating, 0° C to +50° C; non-operating, -40° C to +60° C
  • Humidity: operating, 5% to 80% RH (%relative humidity) at up to +30° C, and 5% to 30% RH above +30° C up to +50° C non-condensing; non-operating, 5% to 80% RH at up to +30° C, and 5% to 30% RH above +30° C up to +50° C non-condensing
  • Altitude: operating, up to 4,600 meters (15,333 feet); non-operating, up to 12,192 meters (50,000 feet)