PIST-2-TDM-PCMCIA-PRO

Features

The PIST-2-TDM-PCMCIA-PRO product has the following features:

PIST-2-TDM-PCMCIA-PRO
  • PCMCIA card
  • 2 T1/E1/J1 interfaces
  • Software switchable between T1, E1, and J1
  • Supplied with two dongles (one for each T1/E1/J1 interface)
  • Two on-board Digital Signal Processors (DSPs) TMS54C5416 with 160 MIPS processing power each
  • Software switchable line termination (High-impedance, 75 and 100/120 ohm)
  • Dongles equipped with software-switchable 20dB signal amplifier and High-Impedance mode for Monitor applications
  • Support for all common T1/E1/J1 Frame Formats and Line Codes
  • Standard DSP firmware supplied with device driver
  • Single bit error simulation mode

Technical Specifications

Board Specification
  • PCMCIA Type II card
Host Bus Interface
  • PCMCIA electrical interface
  • I/O mapped, SW configurable IRQ
Network Interfaces
  • 2 T1, E1 or J1 (software configurable)
Line Termination
  • 75 Ohm and 100/120 Ohm or high impedance
DSP
  • 2x TI TMS320VC5416 with 160 MIPS processing power each
DSP Programming Interface
  • Software development kit in ANSI C and C++
  • Open interface with standard third-party tools
DSP Applications
  • DTMF, MF, FSK, and generic tone (e.g., dial-tone and call progress tone) generation and detection
  • Speech compression, encoding and decoding
  • HDLC processing
  • G.726 ADPCM, G.168 line echo canceller, VAD, AGC, CNG, CPTD etc. (as part of the CST DSP ROM)
T1/E1/J1 Frame Formats
  • Doubleframe, CRC Multiframe (E1 mode)
  • F4, SF (or D4), ESF (or F24), SLC96 (T1/J1 mode)
T1/E1/J1 Line Codes
  • HDB3, B8ZS, AMI, AMI with ZCS
T1/E1/J1 Signaling Types
  • Channel associated (robbed bit)
  • Common channel
Clocking Sources
  • Onboard oscillator
  • Incoming T1/E1/J1 span
Connector
  • RJ45/RJ48C in dongle (two dongles per board)
Testing Features
  • Full access to F, Y, Si, and Sa bits in E1 mode
  • Full access to FS/DL-bits in T1 mode (including support for the DL-channel protocol according to T1.403-1989 ANSI or to AT&T TR54016 specification), and programmable line build-out in T1/J1 mode
  • Transparent mode and programmable transmit pulse shape and input threshold
  • Alarm insertion and detection
  • Loop codes, channel loopback and PRBS
EMC and Safety Testing / Certification
  • FCC Part 15 (CFR47, Part 15, Subpart B)
  • CE EMC (EN61326-1 Class B Equipment, AS/NZS 2064 Class B Limits)
  • Safety EN60950 and UL60950 (dongle only)
Power Requirements / Environmental Data
  • Power consumption: 3.0W
  • Temperature: operating, 0° C to +50° C; non-operating, -40° C to +60° C
  • Humidity: operating, 5% to 80% RH (%relative humidity) at up to +30° C, and 5% to 30% RH above +30° C up to +50° C non-condensing; non-operating, 5% to 80% RH at up to +30° C, and 5% to 30% RH above +30° C up to +50° C non-condensing
  • Altitude: operating, up to 4,600 meters (15,333 feet); non-operating, up to 12,192 meters (50,000 feet)